Eldes ESIM264 Manual de instalación Pagina 124
- Pagina / 140
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
124
9. Monitoring Station
9.1 Basic Overview
The data transmission from ESIM264 alarm system to monitoring station can be carried out by one of the following communication
methods at a time:
• GPRS Network (EGR100/Kronos software protocol)
• Voice Calls (Ademco Contact ID®, 4+2 protocol);
• RS485;
• CSD (fax line).
The system supports 1 primary connection and up to 3 backup connections. All of the aforementioned communication methods can
be set up as primary or backup in any sequence order by EKB2 keyboard, EKB3 keyboard and ELDES Conguration Tool software. For
more details, please, refer to software’s HELP section and chapter 9.3 Monitoring Station Parameter Conguration (SMS, EKB2,
EKB3).
ATTENTION: ESIM264 system is fully compatible with Kronos NET/Kronos LT monitoring station software for communication via
GPRS network. When using dierent monitoring station software, EGR100 GPRS software is necessary. EGR100 is freeware and can
be downloaded at www.eldes.lt
9.2 Data Messages
The conguration of data messages transmitted to the monitoring station is based on Ademco Contact ID®, protocol. The data mes-
sages can either be transmitted to the monitoring station alone or with duplication by SMS messages to User 1 phone number.
The following table provides a list of events supported by ESIM264 alarm system:
Seq. No. Contact ID® Code Description Duplication by SMS
1 1110 Fire Zone Alarm
*
2 3111 Fire Zone Restore
3 1121 Disarmed by User (Duress Password)
**
4 3121 Armed by User (Duress Password)
**
5 1130 Burglary Alarm
*
6 3130 Burglary Restore
7 1133 24H Zone Alarm
*
8 3133 24H Zone Restore
9 1144 Tamper Alarm
10 3144 Tamper Restore
11 1146 Silent Zone Alarm
*
12 3146 Silent Zone Restore
13 1158 Temperature Exceeded
14 1159 Temperature Fallen
15 1301 Main Power Loss
16 3301 Main Power Restore
17 1302 Wireless Sensor Low Battery
18 1308 Device Shut Down
19 1311 ESIM264 Backup Battery Fail
20 1381 Wireless Signal Loss
***
21 3381 Wireless Signal Restore
22 1401 Disarmed by User
23 3401 Armed by User
24 1456 Disarmed by User (Stay Mode)
**
25 3456 Armed by User (Stay Mode)
**
26 1463 Disarmed by User (SGS Password)
**
27 3463 Armed by User (SGS Password)
**
28 1602 Periodical Test
29 1900 Device Started
- INSTALLATION MANUAL 1
- Contents 3
- Installation Manual v2.2 6
- Limited Liability 7
- Manufacturer Warranty 7
- Package Content 7
- About Installation Manual 7
- 1. General Information 8
- 2. Technical Specications 11
- Fig. No.1 12
- 2.3 Wiring Diagrams 13
- Fig. No. 5 14
- Fig. No. 6 14
- Fig. No. 7 15
- Fig. No. 8 16
- Fig. No. 9 17
- 3. Installation 18
- 4. Operation Description 19
- 4.4 Wireless Devices 21
- 4.5 RS485 Interface 21
- 4.6 1-Wire® Interface 21
- 5. Conguration & Control 23
- CONFIGU 24
- XXXX_STCONFIG 25
- Shut down the 26
- Connection with 26
- Set SMS Language 26
- Set SMS Password 27
- Set User Password 27
- Delete User Password 28
- Replace User Password 28
- Set User Phone 30
- Delete User 30
- List User Phone 31
- Numbers 31
- Set Date & Time 32
- Arm the System 33
- Disarm the System 33
- Enable Arm 34
- Disarm by Zone 34
- Disable Arm 34
- Set Zone Alarm Text 35
- List Violated Zones 35
- Set Entry Delay 36
- List Violated 36
- Set Exit Delay 37
- Enable ATZ Mode 37
- Disable ATZ Mode 37
- - Type 1 38
- - Type 2 38
- - Type 3 38
- - Type 4 38
- - Type 5 38
- Disable Zone 39
- Enable Zone 39
- Bypass Zone 40
- Bypass All Zones 40
- Unbypass Zone 40
- Set Zone Type 41
- Enable Stay Mode 42
- Disable Stay Mode 43
- Activate Stay 43
- Mode Manually 43
- Disable Force Mode 44
- Enable Force Mode 44
- Disable Chime 45
- Enable Chime 46
- List Zone & PGM 46
- Output Status 46
- Set PGM Output Name 47
- Turn ON PGM Output 47
- / Set PGM Output 47
- Startup Status (ON) 47
- Example: 1111_C3:ON:13.23.48 48
- [49xx1#] 49
- [49xx0#] 49
- [3312#] 49
- Disable EPGM8 50
- Module Mode 50
- Set Siren Alarm 50
- Duration 50
- See Siren Alarm 51
- Enable Bell Squawk 51
- Disable Bell Squawk 51
- Info SMS 53
- Set Periodic 53
- Disable Periodic 54
- Disable Call in 54
- Case of Alarm 54
- Enable SMS in Case 61
- Loss/Restore 61
- Set Main Power 61
- Loss Delay 61
- Restore Delay 62
- Remote Listening 62
- Enable Control from 63
- Any Phone Number 63
- Disable Control from 63
- Set Keyboard Partition 64
- Switch Between 64
- Keyboard Partitions 64
- Enable Keyboard 64
- Partition Switch 64
- Set Zone Partition 66
- Set iButton® Partition 66
- Disable Event Log 67
- Enable Event Log 67
- Set Microphone Gain 68
- Set Speaker Level 68
- Reset to Default 69
- Parameters 69
- Menu path: 70
- 6.3 Troubleshooting 74
- 7. Wired Devices 76
- MAIN SCREEN VIEW 82
- DISABLE / ENABLE 85
- PARTITION [0... 1] 85
- 7.2 EKB3 - LED Keyboard 88
- FRONT SIDE 89
- AUX- AUX+ 90
- D1 D2 D3 D4 D5 D6 D7 D8 94
- 7.5 EA1 – Audio Output Module 96
- COM DATA 98
- Enable New iButton® 99
- Key Mode 99
- Disable New 99
- Check iButton® Key ID 100
- Delete iButton® Key ID 100
- Add Wireless Device 101
- Wireless Device Info 103
- Test Wireless Device 103
- EWT1 ESIM264 104
- Wireless Expansion 105
- Module EW1 105
- MAGNET SENSOR 109
- 8.5 EWK1 - Wireless Key-Fob 112
- RESETLED 114
- C1 C2 Z1 Z2 COM 122
- 9. Monitoring Station 124
- Enable Monitoring 125
- Station Mode 125
- Disable Monitoring 125
- Disable Data Message 126
- Enable User Message 127
- Disable User Message 128
- Set Account (Alarm 128
- System ID) 128
- Set Primary 129
- Connection 129
- Set Backup 129
- Connection (-s) 129
- Set Server IP Address 130
- Set Delay after Last 130
- Communication 130
- Set DNS1 Server 131
- IP Address 131
- Set DNS2 Server 131
- Set Server Port 131
- Set Protocol 132
- Set Local Port 132
- Set User 133
- Set Password 133
- Set Prole 133
- Set Unit ID 134
- Set Attempts 134
- Set Monitoring Station 135
- Phone Number 135
- Set Test Period 135
- Delete Monitoring 136
- Station Phone Number 136
- For notes 138
- Made in Lithuania 140
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Eldes ESIM264
(28 paginas)
(44 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales