Eldes ESIM264 Manual de instalación Pagina 94
- Pagina / 140
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
94
7.4 EPGM8 - PGM Output Expansion Module
EPGM8 is a PGM output expansion module intended for using with alarm system ESIM264. This module allows to connect up to
additional 8 electrical appliances.
Main EPGM8 features:
• PGM output expansion adding 8 additional PGM outputs.
• compatible with ESIM264 alarm system
7.4.1 Technical Specications
7.4.1.1 Electrical & Mechanical Characteristics
Power Supply 10-24V 100mA max
Number of PGM Outputs 8
PGM Output D1-D8 Circuit
Maximum Commuting PGM Output Values Voltage – 30V; current 500mA
Dimensions 40 x 55 x 15 mm
Range of Operating Temperatures -20...+55ºC
7.4.1.2 Connector Functionality
D1 - D8 PGM outputs
12V Positive power supply contact
GND Negative power supply contact
1 R
OUT
D1 D2 D3 D4 D5 D6 D7 D8
12V GND
Fig. No. 22
Open collector output.
Output is pulled to COM when
turned on.
- INSTALLATION MANUAL 1
- Contents 3
- Installation Manual v2.2 6
- Limited Liability 7
- Manufacturer Warranty 7
- Package Content 7
- About Installation Manual 7
- 1. General Information 8
- 2. Technical Specications 11
- Fig. No.1 12
- 2.3 Wiring Diagrams 13
- Fig. No. 5 14
- Fig. No. 6 14
- Fig. No. 7 15
- Fig. No. 8 16
- Fig. No. 9 17
- 3. Installation 18
- 4. Operation Description 19
- 4.4 Wireless Devices 21
- 4.5 RS485 Interface 21
- 4.6 1-Wire® Interface 21
- 5. Conguration & Control 23
- CONFIGU 24
- XXXX_STCONFIG 25
- Shut down the 26
- Connection with 26
- Set SMS Language 26
- Set SMS Password 27
- Set User Password 27
- Delete User Password 28
- Replace User Password 28
- Set User Phone 30
- Delete User 30
- List User Phone 31
- Numbers 31
- Set Date & Time 32
- Arm the System 33
- Disarm the System 33
- Enable Arm 34
- Disarm by Zone 34
- Disable Arm 34
- Set Zone Alarm Text 35
- List Violated Zones 35
- Set Entry Delay 36
- List Violated 36
- Set Exit Delay 37
- Enable ATZ Mode 37
- Disable ATZ Mode 37
- - Type 1 38
- - Type 2 38
- - Type 3 38
- - Type 4 38
- - Type 5 38
- Disable Zone 39
- Enable Zone 39
- Bypass Zone 40
- Bypass All Zones 40
- Unbypass Zone 40
- Set Zone Type 41
- Enable Stay Mode 42
- Disable Stay Mode 43
- Activate Stay 43
- Mode Manually 43
- Disable Force Mode 44
- Enable Force Mode 44
- Disable Chime 45
- Enable Chime 46
- List Zone & PGM 46
- Output Status 46
- Set PGM Output Name 47
- Turn ON PGM Output 47
- / Set PGM Output 47
- Startup Status (ON) 47
- Example: 1111_C3:ON:13.23.48 48
- [49xx1#] 49
- [49xx0#] 49
- [3312#] 49
- Disable EPGM8 50
- Module Mode 50
- Set Siren Alarm 50
- Duration 50
- See Siren Alarm 51
- Enable Bell Squawk 51
- Disable Bell Squawk 51
- Info SMS 53
- Set Periodic 53
- Disable Periodic 54
- Disable Call in 54
- Case of Alarm 54
- Enable SMS in Case 61
- Loss/Restore 61
- Set Main Power 61
- Loss Delay 61
- Restore Delay 62
- Remote Listening 62
- Enable Control from 63
- Any Phone Number 63
- Disable Control from 63
- Set Keyboard Partition 64
- Switch Between 64
- Keyboard Partitions 64
- Enable Keyboard 64
- Partition Switch 64
- Set Zone Partition 66
- Set iButton® Partition 66
- Disable Event Log 67
- Enable Event Log 67
- Set Microphone Gain 68
- Set Speaker Level 68
- Reset to Default 69
- Parameters 69
- Menu path: 70
- 6.3 Troubleshooting 74
- 7. Wired Devices 76
- MAIN SCREEN VIEW 82
- DISABLE / ENABLE 85
- PARTITION [0... 1] 85
- 7.2 EKB3 - LED Keyboard 88
- FRONT SIDE 89
- AUX- AUX+ 90
- D1 D2 D3 D4 D5 D6 D7 D8 94
- 7.5 EA1 – Audio Output Module 96
- COM DATA 98
- Enable New iButton® 99
- Key Mode 99
- Disable New 99
- Check iButton® Key ID 100
- Delete iButton® Key ID 100
- Add Wireless Device 101
- Wireless Device Info 103
- Test Wireless Device 103
- EWT1 ESIM264 104
- Wireless Expansion 105
- Module EW1 105
- MAGNET SENSOR 109
- 8.5 EWK1 - Wireless Key-Fob 112
- RESETLED 114
- C1 C2 Z1 Z2 COM 122
- 9. Monitoring Station 124
- Enable Monitoring 125
- Station Mode 125
- Disable Monitoring 125
- Disable Data Message 126
- Enable User Message 127
- Disable User Message 128
- Set Account (Alarm 128
- System ID) 128
- Set Primary 129
- Connection 129
- Set Backup 129
- Connection (-s) 129
- Set Server IP Address 130
- Set Delay after Last 130
- Communication 130
- Set DNS1 Server 131
- IP Address 131
- Set DNS2 Server 131
- Set Server Port 131
- Set Protocol 132
- Set Local Port 132
- Set User 133
- Set Password 133
- Set Prole 133
- Set Unit ID 134
- Set Attempts 134
- Set Monitoring Station 135
- Phone Number 135
- Set Test Period 135
- Delete Monitoring 136
- Station Phone Number 136
- For notes 138
- Made in Lithuania 140
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Eldes ESIM264
(28 paginas)
(44 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales