Eldes EKB3 Manual de instalación descargar pdf (Pagina 38)

38 EN

MANUAL ELDES ESIM264 V3.1

12. ARMING AND DISARMING

The system features the following methods to carry out arming and disarming process:

• Free of charge phone call.

• SMS text message.

• EKB2/EKB3 keypad and user password.

• iButton key.

• EWK1/EWK2 wireless keyfob.

• Arm-Disarm by Zone.

• EGR100 middle-ware.

The system arms/disarms the partitions that the preset user phone number, EKB2/EKB3 keypad and user password, iButton key, EWK1 wire-

less keyfob or zone, set up for Arm-Disarm by Zone method, are assigned to. For example, if User 1 phone number is assigned to Partition 0,

the user will be able to arm/disarm Partition 0 by a single phone call to the system (see 23. PARTITIONS).

By default, when the system is successfully armed or disarmed, it replies with conrmation by SMS text message. For more details on SMS

text message regarding system arming/disarming and how to manage it, please refer to 12.9. Disabling and Enabling Arm/Disarm

Notications.

The system will allow to arm the system if the following system faults are present (see 29. INDICATION OF SYSTEM FAULTS):

• Main power supply is lost.

• Low battery.

• Battery failed.

• Date/time not set.

• GSM connection failed.

When attempting to arm the system (by any method, except EKB2/EKB3 keypad and user password, EGR100 middle-ware) in case of violat-

ed zone/tamper presence, the system will reply with SMS text message containing violated zone/tamper number. Due to security reasons

it is highly recommended to restore the violated zone/tamper before arming the system. For more details on how to arm the sys tem despite

the violated zone presence, please refer to 14.6. Zone Attributes and 14.7. Bypassing and Activating Zones

The system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS text messages

containing wrong SMS password even from a preset user phone number. For more details regarding arming/disarming the system from a

non-preset phone number, please refer to 8.1. System Control from any Phone Number.

12.1. Free of Charge Phone Call

To arm and disarm the system, dial the system‘s phone number from any of 5 available user phone numbers (see 8. USER

PHONE NUMBERS for user phone number management). The phone call is free charge as the system rejects it and carries out

arming/disarming procedure afterwards. When arming – the system rejects the phone call after 2 rings, when disarming – the

system rejects the phone call immediately. If there is more than one preset user dialing to the system at the same time, the

system will accept the incoming call from the user who was the rst to dial while other user (-s) will be ignored.

When system’s phone number is dialed for arming, the system will proceed as follows:

• Non-partitioned system:

• If ready (no violated zone/tamper), the system will arm.

• If unready (violated zone/tamper is present), the system will not arm and provide a list of violated zones/tampers by SMS text

message to user phone number.

• Partitioned system:

• If all partitions are disarmed ready, the system will arm them.

• If one or more partitions are disarmed unready (violated zone/tamper is present), the system will arm the ready partition (-s) and

skip the unready one (-s). The system will then send an SMS text message, containing a list of violated zones/tampers, to user

phone number that the system arming was initiated from.

• If a combination of armed and disarmed ready partitions is present, the system will arm the disarmed ready partitions and skip

the armed ones.

1 2 ... 33 34 35 36 37 38 39 40 41 42 43 ... 167 168

Comentarios a estos manuales

Sin comentarios

Eldes EKB3 Manual de instalación Pagina 38

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Eldes EKB3