Eldes EKB3 Manual de instalación descargar pdf (Pagina 62)

62 EN

MANUAL ELDES ESIM264 V3.1

18. PROGRAMMABLE (PGM) OUTPUTS

A PGM output is a programmable output that toggles to its set up state when a specic event has occurred in the system, the scheduled

weekday and time has come or if the user has initiated the PGM output state change manually. Normally, PGM outputs can be used to open/

close garage doors, activate lights, heating, watering and much more. When a PGM output turns ON, the system triggers any device or relay

connected to it.

ESIM264 comes equipped with four open-collector PGM outputs allowing to connect up to four devices or relays. For more details on PGM

output expanding, please refer to 18.2. PGM Output Expansion.

ESIM264 PGM outputs are classied by 4 categories:

PGM output category Description

Max. number of PGM

outputs per device

Max. number of PGM

outputs in total

On-board PGM Outputs Built-in wired PGM outputs of ESIM264 alarm system. 4 4

EPGM8 PGM Outputs

PGM outputs of EPGM8 - hardwired PGM output expan-

sion module.

8 8

EPGM1 PGM Outputs

PGM outputs of EPGM1 - hardwired zone & PGM output

expansion module.

2 4

Wireless PGM Outputs

Non-physical PGM outputs automatically created by con-

nected wireless devices.

2* 32**

* - Depends on the connected wireless device.

** - Available only if no EPGM1 PGM outputs are present.

For PGM output wiring diagram, please refer to 2.3.6. Relay Finder® 40.61.9.12 with Terminal Socket 95.85.3.

18.1. PGM Output Numbering

The PGM output numbers ranging from C1 through C12 are permanently reserved for on-board PGM outputs even if EPGM8 module mode is

disabled. The C13-C44 PGM output number are automatically assigned in the chronological order to the devices connected to the system:

EPGM1 modules and wireless devices.

18.2. PGM Output Expansion

For additional electrical appliance connection, the number of PGM outputs can be expanded by:

• connecting EPGM8 hardwired PGM output expansion module. (see 18.2.1. EPGM8 Mode and 31.3.1. EPGM8 – Hardwired PGM

Output Expansion Module)

• connecting EPGM1 hardwired zone and PGM output expansion module (see 31.1.3. EPGM1 – Hardwired Zone & PGM Output Ex-

pansion Module).

• binding the wireless devices (see 19. WIRELESS DEVICES).

The maximum supported PGM output number is 76.

18.2.1. EPGM8 Mode

EPGM8 is an expansion module, which expands the system with 8 additional hardwired PGM outputs. For more details on EPGM8 module

installation, please refer to 31.3.1. EPGM8 – Hardwired PGM Output Expansion Module.

Once the EPGM8 module is installed, the EPGM8 mode must be enabled.

Enable EPGM8 mode

EKB2

Menu path:

OK → CONFIGURATION → OK → aaaa → OK → PGM OUTPUTS → OK → USING EPGM8 → OK

→ ENABLE → OK

Value: aaaa – 4-digit administrator password.

EKB3

Enter parameter 33 & parameter status value:

33 1 #

Example: 331#

Cong

Tool

This operation may be carried out from the PC using the ELDES Conguration Tool software.

1 2 ... 57 58 59 60 61 62 63 64 65 66 67 ... 167 168

Comentarios a estos manuales

Sin comentarios

Eldes EKB3 Manual de instalación Pagina 62

Comentarios a estos manuales

Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Eldes EKB3